• Maximum load 
  Standard: 100 lbFin [11.5 Nm] 
  Optional:  200 lbFin [22.0 Nm]
• Speed range
  Standard: 0.01 - 15 RPM [0.05 - 90°/s] 
  Optional:  0.04 - 60 RPM [0.2 - 360°/s] *
• Speed accuracy 
  ±0.2% of setting, ±0% variation with load
• Digital display of angle
• Programmable angle limits
• Rotational travel accuracy: ±0.7° / 0.02 rev.
• Rotational travel repeatability: 0.1° / 0.01 rev.
• Rotational travel resolution: 0.1° / 0.01 rev.
• Throat: 4.10" [104 mm]
• Manual adjustment: 12° / adjustment knob rev
• Angle dial with 2° resolution
• Maximum slider travel: 15.5" [394 mm]
• Slider travel rate: 1.047" [26.6 mm] / lever rev
• Universal power supply: 80-250 VAC
• CE mark
• Computer Control 
  An RS-232 port is provided to interface with a PC. A command set is provided to allow for full control from a PC. 
  The following are required with PC control: 
  - Model 7i or 5i force/torque indicator (more info)
  - 09-1162 multi-function cable (see below) 
  - 09-1056 serial cable (see below)
• Digital Angle Indication 
  Rotational travel is indicated in degrees or revolutions, with RS-232 output of angle data.
• Programmable Angle Limits 
  The TSTM-DC can stop at or cycle between programmable upper and lower angle limits. Programmable in degrees or revolutions.
• Overload Protection 
  Protects the torque sensor against overload (requires a Model 7i or 5i force/torque indicator and 09-1162 multi-function cable). The user programs the desired percentage of full scale of the sensor.
• Auto-return 
  The torque table rotates to an angle limit or torque set point (requires a Model 7i or 5i force/torque indicator and 09-1162 cable), stops, and reverses direction at full speed to the other angle limit or torque set point.
• Cycling / Dwell Time
  Same as auto-return, but with the ability to program up to 100,000 cycles. Programmable dwell time for upper and lower limits (set independently) can be set up for up to 10,000 seconds. Independent CW and CCW speeds may be programmed.
• Programmable Button Functions
  Programmable CW and CCW button functions - momentary motion, maintained motion, or auto.
• Independent CW and CCW Speeds 
  Configurable speeds for CW and CCW directions
• Selectable speed units of measurement (RPM and °/s)
• Password protection 
  Prevents unauthorized changes to controller settings.

The TSTM-DC and TSTMH-DC test stands are shipped as shown at left, and 
include the following accessories:

(1) DC controller
(1) Controller connection cable
(1) Indicator mounting kit
(1) Encoder cable
(1) Column cap with hardware
(1) Allen wrench set
(4) Thumb screw for mounting indicator
(1) Power cord 
(1) Resource CD
(1) Base with hardware (TSTM-DC)
(2) Mounting leg with hardware (TSTMH-DC)
(1) Additional column cap with hardware (TSTMH-DC)

** These two upgrades cannot be ordered simultaneously 

The TSTM-DC contains a universal power supply (80 - 240V) and includes a 110V US power cord. Add suffix ‘E’ for Euro cord, ‘U’ for UK cord, or 'A' for Australian cord. 
Ex: TSTM-DCE, TSTM-DCU, TSTMH-DCA

Power cords also available for purchase individually.